Glock 19 Gen 3 Erratic Ejection, a/k/a Brass To Face. *FIXED 5/20/2014

DSCN1308b

So, yet again, I’d intended to do a primer on getting a maintenance kit up and running with all kinds of fun links, opinions on products, and pictures- but yet again, something came up that I thought I’d address immediately.  I still may make this a bonus post, however, and still do the post I’d orginially planned, especially as this one will likely be a to-be-continued as I wait for parts and test solutions at the range.

Right, so on to business- I’ve fallen victim to a problem that seems pretty widespread in late Gen 3 (~2013) and Gen 4 Glock 17s and 19s.  Begin typing “Glock 19 er” into google, and it’ll go ahead and complete that thought for you.

It would seem that many people with these guns are getting the original Glock Perfection(tm) experience for the first 600-1000 rounds, but then, startingly, began experiencing extremely erratic ejection behavior along with several flavors of FTEs.  Mine began at about 600 rounds right on the nose- opened the box of the same PMC Bronze that I’d had zero problems with for more than half of the previous 600 rounds (I’ve been talking this G19 up like crazy, seriously, 0 issues with anything I wanted to feed it, it felt like this thing was magic up until this point).  Was all poised to take this thing up to 650 rounds, and within the first 2 magazines I experienced 2 FTEs and noticed some brass marks on the front of the ejection port.  Made it through 40 rounds with no additional problems before handing the Glock off my lady friend, who, upon commencing firing, was greeted by a hot case-mouth to the cheek, followed by a strike to the forehead.  After clearing and checking the weapon, nothing seemed broken or out of place (aside from previously noticed brass marks on the front of the ejection port), so I loaded another magazine and tested it.  4 of the 15 rounds struck me in the forehead or landed on the top of my head.  1 of the rounds FTEd, and they all seemed to be ejecting fairly weakly.

For reference, here’s the information on this weapon:
Glock 19 gen 3
S/N range: VEX***
Test Fire Date: 6/5/13

So, after taking it down and having a look, then quite a bit of research, and quite a bit of ignoring the fanboys at Glock Talk who will blame any and all malfunctions on sissy wrists and not shooting like a man, I’ve learned the following:

  • At or around Oct. 2010, Glock began to use a different process to manufacture internal parts including the locking block, firing pin, and of note to us here, the extractor.
  • The manufacturing process in question is “MIM” or Metal Injection Molding.  This is in contrast to the previous machined/tooled parts which were of much higher quality.  This was clearly done as a cost-cutting measure.  There have been cases of other manufacturers switching to MIM parts and also having severe quality problems.
  • The QC on the LCI (loaded chamber indicator) extractors, specifically the 9mm ones, seems to have suffered to the point that they’re out of spec, though Glock wont admit it, and many of them have been measured and shown increased distance between the Breech Face and Extractor Claw, allowing too much play with the case as it’s being extracted.
  • This problem, combined with the fine-pointed shape of the original ejector pin (marked 336), has caused the erratic ejection pattern, mostely due to the round bouncing around haphazadly around between the breech face and interior of the slide before finding it’s way out, or not, in the case of the FTEs experienced.
  • Glock has been rather cautious to not put out any direct statements about the problem, but have redesigned the ejector to a more broad shape (now marked 30274), and have been replacing the older ejector on Gen 4 pistols sent in for service that were having this problem.  Sadly, it usually takes a couple of round trips before any progress is made, and even after all that, many people report the problem is not solved.

So, that being said, I’m going to work this out myself, and avoid several months of thumb twiddling each time wondering if my gun is going to come back from Smyrna, GA in working condition, or if it’s just going to nail me in the forehead and/or try to burn my SO’s cheek off again.  I’ll start with the cheap (and in this case, the most widely reported solution), and work my way from there.  First stop, replacing the 336 ejector with the newer 30274 ejector.  Now, since you can’t just buy the ejector, as that would be WAY too easy, you have to buy a replacement trigger housing.  But- they don’t make a gen3 trigger housing with the 30274 ejector (they probably they don’t want to admit there’s a problem), we need to order a gen 4 trigger housing, extract the ejector pin, and swap it into my gen3 trigger housing.  Luckily, it’s an easy enough job, and the new trigger housing is only $9.95.  You may want to go ahead and order a new gen3 housing with the 336 pin in it, and swap those, just so you’re not altering your original in any way, but I’m not going to worry about that.

*UPDATES TO COME*  The first part is in the mail, later updates will come.  Just in case you’re following along and want to go ahead and get all parts in one go and not have to play the waiting game in case the ejector doesn’t fix your problem- my plan B is either swapping in a Lone Wolf Extractor or (more interestingly) swapping in a .45ACP extractor used on the G21/30.  This has reports of being a good fix, because the parts are dimensionally similar enough to fit, and the .45 extractor has a slightly shorter gap between breech face and claw.  It also holds the case at a slightly different angle, more reminicent of the older non-LCI (loaded chamber indicator) extrators on gen 2 Glocks (back when they worked like a charm).

UPDATE #1

Thanks to Mr. Humke at GlockParts.com, LLC, I received my new Gen4 Trigger Housing with the 30274 ejector within 3 days.  The difference between the new one and the older 336 ejector was pretty huge.

DSCN1319

Sadly, due to my schedule, I haven’t been able to get back to the range to test it just yet, but hand-cycling snapcaps produced a perfect pile at the weapon’s 4 ‘o clock, so we’ll see.  *UPDATES TO FOLLOW*

As for the installation, I’d say if you’re comfortable field stripping, this isn’t too much of a stretch.  The Glock is easier to work on than I thought, they weren’t kidding when they say how few parts there are.  The only tools you’ll need are a punch, preferrably a Glock Disassembly Tool (pictured below) and a tiny flathead screwdriver. After removing the slide from the frame, you’ll need to use the tool to push out the marked pins from the frame.  These are different sizes, so be sure to keep track of which one’s which (though it’s easy, big, medium, small, from front to back).

glock toolpins

After this, you’ll need to use something to pry up the Locking Block (pictured below).  It should come right out rather easily.  When removing this, note the position of the Slide Catch Lever, you’ll need to put this back in afterwards.

Locking BlockAfter the Locking Block is out, you’ll be able to remove the Trigger (along with the Slide Catch Lever) and Trigger Housing out of the frame.  You can disassemble further, but this is really as far down as you need to go.  The Ejector pin simply pulls forward out of the Trigger Housing, though you’ll likely need to use the flathead to push it from the rear to get it started (you can see rear of the Ejector pin at the rear of the Housing).  After getting it far enough out, either pull out with your hand, CAREFULLY use the screwdriver to pry it out from the front, or use a pair of needle nosed pliers (you’ll want to wrap cloth or electrical tape so as to not scratch) to pull the pin out the rest of the way.

Once you have both pins out, push the 30274 ejector into the Gen3 housing, making sure it’s fully seated, and reassemble your weapon in reverse order.  The only tip I have here is to get the Slide Catch Lever in place after the trigger, then put on the Locking Block, which compresses the spring.  Use your Glock Disassembly Tool to help align things when reinserting the roll pins.

DSCN1316DSCN1318

UPDATE #2: Confirmed Fixed.

IMAG1506

Well, there we have it folks.  Fired 65 rounds today, nearly all perfect 4-5 o’clock ejections with one stray towards 6 o’clock, but soared a few feet over my head.  I think we have a winner.  Time (well, a few hundred more rounds) will tell, but based on how miserable the last 35 rounds were prior to replacing the ejector, compared to how it performed today, I’m going to have to call this one a win.  GLOCK- please start using the 30274 ejector in all current production 9mm models, not just the Gen4 models.  That is all.

86 thoughts on “Glock 19 Gen 3 Erratic Ejection, a/k/a Brass To Face. *FIXED 5/20/2014”

  1. I too own a Generation 3 G19 and absolutely hate when the slide jams half open. FTE, I believe you called it. Not too reliable! But it’s a Glock. Indestructable Glock. Another thing that I hate is hot brass binging me in the face. Now I find out that Glock KNOWS about this failure in design and practice.
    I also have a XDS 45. No one enjoyed the recall on their XDS, but they recalled them and they got repaired, the 1st time.
    Why can’t Glock stand behind their products?

    1. I’m with you Kevin, I’m not sure why they wouldn’t just recall these, seeing the amount of reports of this problem I’ve run across, especially since they seem to have addressed the cause in their Gen4 guns, and it’s a cheap, easy fix at that. I’ve even seen reports of people having it sent to Glock, and a return trip with no changed parts with a “no problems found.”

      Lucky for us, the fix is cheap and fairly simple. Did you manage to try the fix mentioned above on yours? Seems to have fully cleared up the problems with mine.

    2. I wish I could tell you, but in all honesty, and I hate to say it, this tends to happen any time a european manufacturer starts making their products in the United States (Sig and Beretta, for example).

      As mentioned in the article, it seems to have started around the time they started cheaping out on the parts and going with MIM vs. forged. Cut corners and you’ll lose quality, simple as that.

  2. Have the same problem.. Can’t wait to fix it because I really like the G19. But just found out the Gen 4 part is on back order. I guess there are a lot of G19s out there with the same issue.

    1. Looks like Lone Wolf has them in stock at the moment- http://www.lonewolfdist.com/Detail.aspx?PROD=123268

      Part number mentioned is different, but that may just be their internal part number. This is the same Gen 4 trigger housing with the 30274 ejector as the one linked in my original post. If you haven’t found it elsewhere yet, this may be your best bet.

      Since writing this article, I’ve had ~600 rounds through the same G 19 with no problems, so this definitely fixed the issue for me.

      Good luck, and let me know how it turns out!

      1. I know this is an old thread, and hopefully you will get this message, I am having the same problems with my Glock and I’m trying your fix. What about finding an old-style non-LCI extractor and bearing in 9 mm instead of 45? Do you think installing the old style extractor would work?

        1. While it *probably* would fix it, since that seems to be the change that caused the problem – I can’t say for sure since I haven’t tested it.

          The reason I tested the above method was because it uses commonly available new-production parts that are easier to locate.

          In any case, if you try swapping the extractor with an older production one – esp. if you find a good source of ’em, be sure to let me know the results, and I’ll update this article with the info.

          1. kylebix5 on eBay Has sold 78 of the old-style 9 mm non-LCI extractors. I just bought mine from him and also the bearings are on eBay as well. But it says he is almost out of them. My current day June for extractor should be here tomorrow. I will install it in my G 19 and get back to you. Great website you’ve got. Keep it up

          2. Also, There is a new part number for that extractor is well. 30275, and it shows to be for the 9 mm is well. I am thinking either one will fit

  3. I have the same problem with my gen3 19, serno XFGxxx, from late Aug, 2014. I’ve swapped the ejector AND the extractor but still have the problem. In fact, I’ve been dodging hot casings all morning. Have no idea what to do next.

    My old gen 2 from 1998 still purrs along just fine.

  4. I have a G19 RTF2 gen 3 and the 30274 housing does not seat in the frame. The housing is deeper on the 30274 opposed to the 336.

    1. As was mentioned in the guide, you’re not putting the 30274 housing in, you’re pulling the ejector pin out and seating it into the 336 housing in order for it to fit.

  5. I just purchased a gen 4 19 and it has the new 30274 ejector and I still get brass in the face and to my Leeds shoulder..WTF! Any one have any ideas? I have 400rds through her! And I have watched video of extractor change not fixing it either..and help would be greatly appreciated

    1. Yeah, get rid of it- I tried all that with my G19 Gen3 and none of it worked- called Glock they were and still are extremely rude and talk down to you denying the problem even exists- I fixed the problem alright, I got rid of it and bought a Beretta 92FS-

  6. Try a Lonewolf extractor which in a non dipped extractor and a lot better fit and finish than the OE one and a sp01176 loaded bearing non LCI style
    Has been known to solve the problem.

  7. Same problem with my Gen. 3 19.
    99% cure with the 30274 ejector.
    Final 1 % was cured by installing a NON- SLB which puts a tad more spring pressure on the original extractor that came on the 19.

  8. Hey there would you mind letting me know which hosting company you’re utilizing?
    I’ve loaded yoir blog inn 3 completely different internet browsers
    and I must say this blog loads a lot faster then most. Caan you suggest a good hosting provider at a fair price?
    Thanks a lot, I appreciate it!

  9. I just picked up a Gen 2 Glock 17 with a lot of miles on it.

    Its ejection is wimpy at best, with several different brands of 9mm 115gr FMJRN practice ammo, and I get brass to the face 50%+ of the time. A Glock armorer has looked at it and said there isn’t anything obvious wrong with the extractor, spring, plunger, or ejector. Any suggestions on where to begin? One of the Lone Wolf extractors, maybe? Replacing the extractor spring?

    1. Honestly it’s a bit surprising hearing of problems with a Gen 2, those things tend to be the standard by which others are judged and found wanting.

      As you mention, miles on it, so obvious things to do would be change out the springs, and maybe try the fix posted here if that doesn’t clear things up.

    2. I used the LONE WOLF extractor then bought a latest and greatest Gen 5 19x trigger housing and swapped the ejector. So far so good. No issue – NONE. BUGH THE g5 housing fro Optics Planet or $12 the extractor is pricey though and had to spend a couple more bucks on an LCI bearing, etc.

      Since then I noticed Glock Store has a Replacement extractor with bearing. Never used. So can’t speak for it but it is milled aluminum not MIM. THEY WERE LIKE $30 instead of the $50 I spent on the Lone wolf parts…

  10. Hey there! I’ve been reading your website for quite some time now lastly got the bravery to just offer you a shout out from Humble Texas!
    Just wanted to say maintain the great work!

    1. Thanks for the shout out, I’m really surprised by the amount of traffic this post in particular continues to get.

  11. naturally like your website but you need to check the spelling on quite a few of your posts.

    Several of them are rife with spelling problems
    and I find it very troublesome to tell the reality then again I will surely
    come bac again.

    1. Well first off, thanks for coming by and commenting, I appreciate the traffic and feedback. I usually try to proof read everything, but sometimes things will slip through and I’ll notice it later, or when someone else reads it and lets me know. I also use some jargon and slang that might not necessarily be dictionary friendly, but do feel free to point out any obvious offenders.

      Again, thanks for reading, and thanks for the comment!

  12. Make sure that your energy cards match the type of your deck.

    Every Pokemon league has eight badges, so the badges will come in types that you can choose from to
    match one of the eight preset badges needed for that league.
    This would give the game more levels, texture, and guesswork.

  13. Brand new G34 Gen4 MOT, has brass to face problem out of the box and glock changed the followers under warranty which made it into a brass to shoulder problem. Customer service representatives were rule and dismissive, blaming the ammo and the shooter.

    Seems like the only fix is to take a loss and trade this piece of trash for something else. My first and last Glock. So much for their “perfection”.

  14. The second trip to the factory made it much worse. The brass now hits head, shoulder and chest. It comes straight back ever shot!

    I bought it new in July, used it twice in a range, got peppered with hot brass and it spend more time at the factory then in my possession. Glock customer service is rock bottom bad. I took a loss of $350 and traded this piece of complete garbage and bought a new Dan Wesson .357 revolver. It

    1. Sorry to hear it, especially this late into the release of the Gen4 guns. I’d love to know what internal changes they made for the “M” models that passed FBI trials and are slated for adoption, but that they still have frequent reports of erratic ejection on new guns is unforgivable, especially since this all started when they cheaped out and started using MIM parts instead of forged.

  15. Hello there, You’ve done an incredible job.

    I’ll certainly digg it and personally recommend
    to my friends. I am confident they will be benefited from
    this website.

  16. Sorry about the delay. There was some miscommunication with someone about sending the gun back to Glock.

    Anyway. I sent that Gen 2 G17 back to Glock a couple of weeks ago, and it looks like they received it on February 7th, and–if I am reading the letter that came with it correctly–replaced the extractor plunger, the striker, the firing pin, the disconnector, and the magazine (!) and shipped it back to me the same day.

    I took it to a range Saturday morning… and nothing has changed. It is still smacking me in the face with ejected cases. I’ve tried brass case and steel case, hollowpoints and ball, factory and reloads, and it happens with all of them.

    To say that I am a bit frustrated now would be an understatement.

    1. Status update.

      500+ rounds later, it’s not changed. Several times in every mag it throws the ejected cases right at my eyes. It matters not whether I hold the gun in a death-grip or deliberately try to limp-wrist it by shooting it weak hand only, whether the ammunition is Winchester White Box 115gr that barely cycles the slide, or hot Israeli SMG ammo. Brass case or steel, bullet weights from 115gr to 147gr, it’s all the same, standard pressure, +P, or NATO.

      I am greatly annoyed because otherwise the gun has not had any failures to feed, extract, or eject, and I shoot it fairly well.

  17. I was excited to discover this great site. I want to
    to thank you for ones time due to this fantastic read!! I definitely loved every bit of it and
    i also have you book marked to look at new stuff on your blog.

  18. Just purchased g19 gen3 one month ago.
    Within two mags brass to face 3 times 2 to shirt pocket. Two purchases in one.
    First and last.

  19. just purchased a gen 3 g19. I have the same 336 ejector, my s/n is all i have since no fired casing was included in my purchase. can anyone advise what year this gun was made, BEBA896. its pretty sad to purchase a 500.00 dollar firearm just to hear it may be JUNK right out of the box .fingers crossed .

    1. That’s a pretty early S/N, so you may be okay. Even if yours is one of the affected ones, replacement of that ejector shown above is pretty easy, and in *most* cases clears up the issue. Since correcting it, this is one of my go-to EDC guns, and brass-to-face issue aside, I’ve never experienced a failure of any kind. Be sure to let me know how it goes when you get a chance to shoot it!

    2. The serial number is a very recent manufacture, not an early one. But if you call Glock, they can run your serial number and tell you what year it was made. I’ve done it many times. Hope this helps.

  20. Well,heck, I was about to order a G 19 but after reading this,I think I’ll pass. Thanks for saving me the trouble

  21. Have you ever thought about creating an ebook or gest auuthoring onn other websites?
    I have a blog centered on the same subjects you discuss and woulld love to have you share some stories/information. I know my subscriibers would
    value your work. If you’re even remotely interested, feewl free to send me an e-mail.

  22. I feel this is oone of the sso much vital info for me. And i’m glad reading
    your article. But wanna commentary on some basic issues, The webb site style iss
    great, the articles iis truly great : D. Good task, cheers

  23. Everytime you would like to uncover more about this specific area go to:
    bongacams tokens generator obtain Token are the digital currency of Bonga Cams, and
    are purchased by way of a quantity routes (as shown under).

  24. It’s a shame you don’t have a donatee button! I’d certainly donate to this outstanding blog!
    I guess ffor noww i’ll settle for bookmarking and adding your
    RSS feed too my Google account. I look forward to fresh
    uprates and will share this website with my
    Facebook group. Talk soon!

  25. Changing to a 30274 ejector cured 99% of my ejection problems and installing a non-LCI Spring Loaded Bearing cured the remaining 1% .
    Now I can even shoot lightly loaded ammo with no ejection problems .

    1. Did you use the non lci slb (longer one) with the stock lci dipped extractor? I have 2 gen 3 Glock 17 new production and I’m changing out the 336 for the 30274 ejector I was getting random brass to the face from the beginning. These have the 15 degree lci dipped extractor

  26. My P80 G19 was ejecting ok but not great, with an occasional round to my face, so I replaced the Gen 3 ejector with Gen 4 ejector. Now it very consistently ejects every single casing in my face!

    1. Well, there’s something to be said about consistency, at least! Sorry to hear it didn’t work for you – in mine and many others changing the ejector helped. Could try going with a different extractor to see if that changes things, sadly, I don’t think we’re ever getting an answer from Glock on issues with the Gen 3s at this point.

  27. Hello,
    I want to tell yyou thzt I’m using your site for a long time and you post really good info.
    I shared you latest article on twitter and got a lot of positive feedbacks.

    Waiting for yoour next article

  28. I have enjoyed this page just for the info as I FINALLY seem to have my issue resolved. I went with aGten 5 19x trigger housing and swapped ejectors. But then to ge forceful morecnsitnt had to cave and drop abou $50 on the Lone Wolf upgraded extractor and LCI bearing , etc.

    Recently though I noticed Glock Store has their own CNC machined , not MIM, extractor with the bearing for about $30. So not quite as painful… curious to k now if they help. as I know others with this issue…

  29. Wow! Such an excellent and helpful post this is. I love it. It’s so good and so perfect. I am just amazed. I hope you continue to do your work like this in the future also, thanks.BERETTA 92FS

  30. Thanks for sharing an interesting blog. G17L Long Slide Google is trying to determine good content with a headline and then look for a keyword or phrase when this can be very difficult to get in a title that would actually attract a reader.

  31. Pretty good post. GAMO GX 40 PCP I just stumbled upon your blog and wanted to say that I have really enjoyed reading your blog posts. Anyway, I hope you post again soon. Big thanks for the helpful info.

  32. It is very easy to understand at a glance. It is very useful! especially for me. Very informative.
    Thank you for the share
    First I want to thank you for posting such an amazing article which is really very helpful and I read your complete blog. I found Aguila 5.56mm NATO 55 gr something new here so thank you again and keep posting and updating with new things.

  33. The advancement of technology has positively influenced the growth of businesses all over the planet.
    With the help of modern technologies like websites and mobile applications, every firm can sell its products
    or services online without hassle. We, QuikieApps,Skittles Edibleshave acquired recognition and reputation through the reliance
    of our respected clients as the top Web development company in Bangalore, India, USA, UK, Dubai. Adapting the dynamic
    technology of the web and mobile applications is the first step to success in this modish and competitive world.

  34. The advancement of technology has positively influenced the growth of businesses all over the planet. Kimber Stainless TLE II
    With the help of modern technologies like websites and mobile applicationsevery firm can sell its products
    or services online without hassle. We, QuikieApps,have acquired recognition and reputation through the reliance
    of our respected clients as the top Web development company in Bangalore, India, USA, UK, Dubai. Adapting the dynamic
    technology of the web and mobile applications is the first step to success in this modish and competitive world.

  35. Your blog post on the “Glock 19 Gen 3 Erratic Ejection, A/K/A Brass to Face” addresses an issue that’s crucial for firearm enthusiasts and Glock owners to be aware of. The erratic ejection problem, also known as “brass to face,” https://jetx-now.com/crash-gambling-games/ can be not only uncomfortable but also potentially dangerous, so it’s essential to discuss and find solutions.

    I appreciate your in-depth analysis of the problem, its potential causes, and the various remedies you’ve suggested. It’s evident that you’ve done thorough research and have practical knowledge about the Glock 19 Gen 3. Your troubleshooting tips and recommendations for aftermarket parts offer valuable insights for Glock owners facing this issue.

    Moreover, your blog post serves as a helpful resource for Glock enthusiasts who may encounter similar ejection problems with their firearms. It not only provides solutions but also encourages responsible firearm ownership by advocating for professional gunsmithing services when needed.

    Addressing firearm issues like erratic ejection is essential for maintaining safety and ensuring a positive shooting experience. Your blog post contributes to this effort by shedding light on the problem and offering practical solutions. Thank you for sharing your expertise on this topic and providing guidance for Glock owners facing this particular challenge.

Leave a Reply

Your email address will not be published. Required fields are marked *